Measurement Of Free-Fall Acceleration Essay, Research Paper
Measurement of Free-Fall Acceleration
Introduction
Galileo Galilei (1564-1642), the man first accredited with the correct notion of free-fall with uniform acceleration, stated that “if one were to remove entirely the resistance of the medium, all materials would descend with equal speed.” Today, this statement holds true for all objects in free-fall near the Earth s surface. The purpose of this experiment is to verify Galileo s assertion that acceleration is constant. In addition, the magnitude of acceleration will be calculated.
Theory
By definition, acceleration is the rate of change of velocity with respect to time. Instantaneous acceleration is the derivative of velocity with respect to time.
a(t) = dv / dt.
Average acceleration is the change in velocity during a time interval, Dt, divided by the length of that interval,
aave = Dv / Dt.
In this experiment, average acceleration of gravity will be determined by measuring the change in position of a falling object at regularly timed intervals. With this, average velocities for these intervals will be calculated. A graph of the average velocities versus time should give a straight line whose slope is the acceleration of gravity (g).
Apparatus
To determine the acceleration of gravity the Behr apparatus will be used. The device consists of two vertical conducting wires, a thin strip of paper held between them, and a metal-girdled weight designed to fall between the wires along the length of the paper strip. A spark timer transmits a high voltage electric pulse to the wires approximately 60 times a second. Every time a pulse is transmitted, two main sparks flow through the system. One spark passes from one wire to the metal girdle around the weight. The second spark causes a small burn in the paper, marking the location of the weight at that instant.
Procedure
Turn on the electromagnetic power supply and suspend the weight from the end of it. Confirm that the weight falls smoothly into the cup at the base of the apparatus when the electromagnet switch is turned off. Run this test run about three or four times before you continue. Next, draw a fresh strip of paper from the base of the device and clamp it in place. Turn on the electromagnet, and suspend the weight at the end of the magnet. Hold down the spark switch, and then immediately turn off the eleectromagnet power supply. The weight should fall down to the base of the apparatus, causing sparks to pass between the two wires and itself. Turn off the power to the spark timer and inspect the paper strip. A series of burns should be visible along the length of the paper. Remove the paper strip from the apparatus and immediately mark the spots with a pen or pencil to see them more clearly.
Data and Results
The following table
Calculations of distance, velocity, and acceleration of metal girdle.
n x n (cm) xn+1 – x n (cm) xn+1 – x n / Dt = v n (cm/s) vn+1 – v n (cm/s) vn+1 – v n / Dt = a (cm/s2)
1 0.00
2 0.70 0.70 x .02 42.1 x 2
3 1.43 0.73 x .04 43.9 x 3 1.8 x 5 108 x 302
4 2.43 1.00 x .04 60.2 x 3 16.3 x 6 981 x 373
5 3.72 1.29 x .04 77.7 x 3 17.5 x 6 1054 x 373
6 5.27 1.55 x .04 93.3 x 3 15.6 x 6 939 x 372
7 7.07 1.80 x .04 108.4 x 4 15.1 x 7 909 x 432
8 9.16 2.09 x .04 125.8 x 4 17.4 x 8 1047 x 494
9 11.5 2.32 x .04 139.7 x 4 13.9 x 8 837 x 491
10 14.1 2.61 x .04 157.1 x 4 17.4 x 8 1047 x 494
11 17.0 2.90 x .04 174.6 x 4 17.5 x 8 1054 x 494
12 20.1 3.15 x .04 189.6 x 5 15.0 x 9 903 x 552
13 23.6 3.45 x .04 207.7 x 5 18.1 x 10 1090 x 615
14 27.2 3.65 x .04 219.7 x 5 12.0 x 10 722 x 610
15 31.2 3.98 x .04 239.6 x 5 19.9 x 10 1198 x 616
16 35.4 4.20 x .04 252.8 x 5 13.2 x 10 795 x 611
17 39.9 4.52 x .04 272.1 x 6 19.3 x 11 1162 x 676
18 44.7 4.72 x .04 284.1 x 6 12.0 x 12 722 x 731
19 49.7 5.00 x .04 301.0 x 6 16.9 x 12 1017 x 734
20 55.0 5.33 x .04 320.9 x 6 19.9 x 12 1198 x 736
21 60.6 5.60 x .04 337.1 x 6 16.2 x 12 975 x 734
22 66.5 5.87 x .04 353.4 x 7 16.3 x 13 981 x 794
23 72.5 6.07 x .04 365.4 x 7 12.0 x 14 722 x 851
24 78.9 6.35 x .04 382.3 x 7 16.9 x 14 1017 x 855
25 85.8 6.68 x .04 402.1 x 7 19.8 x 14 1192 x 857
26 92.7 6.93 x .04 417.2 x 7 15.1 x 14 909 x 853
27 99.9 7.15 x .04 430.4 x 7 13.2 x 14 795 x 852
28 107.4 7.46 x .04 449.1 x 8 18.7 x 15 1126 x 916
29 115.0 7.74 x .04 465.9 x 8 16.8 x 16 1011 x 975
30 123.1 8.01 x .04 482.2 x 8 16.3 x 16 981 x 975
31 131.1 8.20 x .04 493.6 x 8 11.4 x 16 686 x 971
32 139.9 8.55 x .04 515.0 x 8 21.4 x 16 1288 x 978
33 148.7 8.80 x .04 530.0 x 9 15.0 x 18 903 x 1034
aAVE = 9.47 x .69 m/s2 s = 9.47 x .78 m/s2 slope (m) of graph = 8.9
Conclusions
The average value of acceleration for each time interval is closer to the desired value of 9.8 m/s2 than the calculated slope of the velocity-time graph. The average of uncertainties for the calculated accelerations is a better as choice of uncertainty because it provides a narrower field of uncertainty than does standard deviation. In conclusion, the calculated value of 9.47 x .69 m/s2 for acceleration is acceptable.
352